Full Range of Filtration Media, Strainer Cages and DIY Filter Related Products. Helps to remove ammonia and nitrate. Designed for moving & static bed filters - helps increase filter efficiency.
Sinking and neutral buoyancy Medias Available. Injection Moulded to ensure a high quality is maintained.Class leading total surface area. Bio-Plas filtration media is made from 100% recycled plastic.
Bio-Plas Filter Medias are suitable for use in mechanical and biological filtration systems. All types of Bio-Plas filter media provide large surface areas for good bacteria to colonise and this increases the efficiency of a box, pressure or multi-bay pond filter. Bio-Plas Medias provide the maximum active surface area for the bacteria to colonise, much more than other types of static media.
It is this process which removes harmful ammonia and nitrite from the water. Within the media is a protected surface which enables colonies of bacteria to naturally follow their lifecycle, of maturing, dying and then fuelling the latter stages of the nitrification cycle.All Bio-Plas filtration media can be used in either a. Mechanical or biological Filtration system; Bacteria will colonies while collecting debris and plant material from the pond with no compromise water flow. Bio-Plas Micro is different from other medias as it move within the filter and cause old dead bacteria on the outside of the wheel to be displaced, leaving space for new bacteria to rapidly develop. Filter maintenance time can be reduced by using Bio-Plas Micro, designed to freely move in a filter, this movement causes the media to self clean as it turns unlike foam and static filter media that require removing and cleaning.
This self cleaning process allows the filter to be effective without the disturbance caused by regular cleaning as it avoids the unnecessary loss of vital bacteria. Bio-Plas Micro (Size Per Piece14mm Dia x 9mm). (Size Per Piece 20mm Dia x 60mm). (Size Per Piece 55mm Dia x 52mm). (Size Per Piece 38mm Dia x 16mm). (Size Per Piece 60mm Dia x 23mm). All media in the Bio-Plas range are different in size, buoyancy and colour. Depending on the application and budget Bio-Plas will have a filtration media suitable for you. All Bio-Plas Filtration Media is manufactured in England.A Bio-Plas sack will be supplied with every individual 20 litre. Litre of Media converted to a volume. 1000 liters = 1000000cm3 (1 Cubic Meter). The Aqua-Jet Air Diffuser HI-BLO Aerator has been specially developed for situations where a high concentration of aeration is needed, whether this be for fluidized beds in your filter system or out in the pond. It is important to use a powerful air pump (depending on the size of the filter bed).
Recommended Air pump Size: 40-60LPM (for normal aeration situations). Supplied with 10 meters of clear flexible P. Drawstring Nylon Mesh Filter Bag. These filter media bags are designed for filtration applications. The bags hold carbon, ammonia remover resins or any other type of filter media.
Keep media in these bags to prevent fines from washing out. These bags provide a convenient way to customise pond, tank and aquarium filtration.
Allow precise placement of filter media. Prevent media from entering your filter system. Great for bio-balls, activated carbon, ceramic and ammonia remover.Drawstring closure for reusable purpose. Bio-Plas Filtration Sacks have been designed for use with filtration media, each sack will neatly contain 20 liters of filtration media. The Filter Webb is one of the best products for polishing the water and for the size of the Filter Webb the surface area it offers to catch micro-particles is amazing. Super easy to easy to clean, just pop the Filter Webb in to a clean bucket of water and plunge up and down a few times and it will release the fine particles it has trapped, repeat till the water is clean. This Filter Webb works the same was as foam but better, not only does it offer more filtration capability but due to its design it is really easy to clean all the fibers/pours of the webb, unlike foam.
Filter webb 300 = 300mm dia/100mm in depth Filter webb 450 = 450mm dia/100mm in depth. The Filter Grids are made of non-toxic polypropylene so are ideal to use as baffle boards and filter media support trays, the open grid design allows a free flow of water and will give excellent strength and support. A must if you are building your own Filtration system. The filter grid is easy to cut making it ideal if the user has a round tank/filter. Filter Grid size L 680mm x W 400mm x D 12mm.
The Multi Grid is a carefully designed clip-together Filter Grid that requires no additional fastenings or fixtures but gives excellent strength and support. Regardless of the size of the application, the Multi Grid can be connected together to make a grid to suit.Ideal for large baffle boards, filter media support trays in filter systems and dividers in grow tanks the open grid design allows a free flow of water. The Multi Grid is easy to cut making it ideal if the user has a round tank/filter. Multi Grid size L 300mm x W 300mm x D 12mm.
6 Multi Grid will be included (a combined size of 60cm x 90cm). Manufactured from a transparent Polymer, ideal for dividers in a tropical fish tank. Filter grid Topper has been designed to reduce the grid size on the popular filter grid.
The original grid size is 18mm x 18mm; the addition of the Grid Topper kit will reduce the grid size down to 7mm x 7mm. This is ideal if you are using a small/fine media in your systems. One Grid Topper kit is meant for one filter grid (680mm x W 400mm x D 12mm) the Grid Topper kit sits just shy of the outside edge of the grid. What Comes With The Kit?The kit is supplied with 5 Grid Toppers (130mm x 383mm) and 10 pairs of Clips. The kit will have to be assembled once arrived. The clips come in two halves that simply push/snap together, please note once the clips have been secured to each other they are not designed to come apart and you risk breaking them.
The strainer will stop large debris from going into the actual filter. The strainer has been designed to be attached to any 110mm/4 fitting; the strainer cage is manufactured with a joining spigot of 110mm OD. All 110mm/4 fittings such as bends and tees will mount directly onto the strainer itself (if you require any further information on sizing please look at our pipe identification chart supplied). The strainer can also prevent fish from disappearing through the pipework. This strainer is also perfect for using in-between ports/inlets in your filter.
Stopping any media from leaving its intended chamber. The strainer has been designed to be cleaned/maintained easily. Simply remove the 4 threaded nuts from the top plate of the strainer; this will give access to the inside. The range of strainer cages are supplied with a range of different fittings to suite most requirements, please select the configuration that is required from the drop down menu. Please Note: This fitting is solvent weld.
Cage Size: H-155mm W-200mm L-240mm. Cage Size: H-160mm Dia - 280mm. Due to popular demand, the large Multi Strainer cage has been brought to the market. The multi-strainer enables two or more strainer cages to be joined together. Ideal for large filter beds or grow tanks.The connectors of each strainer simply push together; the addition of a non-toxic solvent weld adhesive will ensure a permanent fit. Please note: 1 Multi Strainer will be included but will need the addition of one of the large round strainer kits. The strainer has been designed to be attached to any 2/56mm rigid pipe, with the addition of a removable nut.
This allows for a secure/tight fit but is easy to clean by just unthreading the nut. Stopping any media from leaving its intended chamber in filters such as moving beds. This strainer will fit any 2/56mm (OD) pipe work or fittings.
The small strainer cage is supplied in several different configurations to suite most requirements. Small Strainer/Cage from a 2? The removable strainer/cage from a 2?
/56mm threaded tank connector kit comes with all the necessary parts to connect your strainer to a tank/filter box. The kit will come supplied with the removable strainer, 56mm-56mm internal joiner and a 56mm threaded tank connector. (Please refer to our thread tank connector chart for more information on dimensions). The kit will come unassembled so this enables the customer to choose a configuration appropriate for the application that they need. The 56mm threaded tank connect has a double socked design enabling it to receive rigid pipe/fittings on either side. Small Strainer/Cage from a 2? /56mm Threaded Tank Connector and 43mm hosetail (Small). The removable strainer/cage from a 2?/56mm threaded tank connector and 43mm hosetail kit comes with all the necessary parts to connect your strainer to a tank/filter box. From a flexi hose feed/return. The kit will come supplied with the removable strainer, 56mm-56mm internal joiner 56mm threaded tank connector, 56mm-43mm reducing bush and a 43mm hosetail. This hosetail can be used in-conjunction with flexible hose with an internal diameter (ID) of 20mm (3/4? Small Strainer/Cage from a 2?
/56mm Threaded Tank Connector and 50mm hosetail (Large). The removable strainer/cage from a 2? /56mm threaded tank connector and 50mm hosetail kit comes with all the necessary parts to connect your strainer to a tank/filter box. The kit will come supplied with the removable strainer, 56mm-56mm internal joiner 56mm threaded tank connector, 56mm-50mm reducing bush and a 50mm hosetail.
This hosetail can be used in-conjunction with flexible hose with an internal diameter (ID) of 30mm-40mm-50mm. Double Removable Strainer/Cage from 2?
Strainers are ideal for any inlet or outlet pipe work on filters. The double strainer was designed for larger ponds/filter systems where a larger flow of water is required. This kit has not been assembled allowing you to build it in different configurations tailor made to your filter/pond setup. What is supplied in the kit? 5 x 2"/56mm - 2"/56mm internal joiners.